Відео

terrible attempt at proper repair

Considering what that fender used to look like this is a huge improvement. Good to see you’re still at it. keep up the good work. Looking forward to more of the progress on this.

This is super informative!

I was looking at some of the harbor freight hammer and dolly sets. It was recommended to me to have them polished due to factory blemishes. That is a nice color combo. Good work straightening out that fender

4:12 pretty simple? I can't get the lock rod for the handle off. It seems impossible.

4:12 pretty simple? I can't get the lock rod for the handle off. It seems impossible.

Can so mark measure with a tape both sides for the new install 😊

when i try to floor it it wont go past 40 n my car jerks, could this be the solution??

Tranny fluid is shooting from from covering the front wheel

Should have a mask on bro

I have a 93 3.8 Sable that ran hot one day and assumed it was the headgaskets and never drove it again less than 100k just sad to see it as a dust collector now it was my first car ❤

Is that the ford or safety blue?

shitty vid

would this work for 1997 jeep grand cherokee?

Were u buy your blue paint

It looks like your sway bar bushings are shot also ..the ones that end of sway bar plugs into. They are pressed in..but are fairly cheap and can be removed without removing all the stuff you just put in..

I have a 98 mustang 🐎 3.8 automatic that I believe has a blown head gasket as well . Just hope it isn't a crack engine block . Not looking forward in this repair

Will this work for a 1990 aswell?

Clockwise counterclockwise?? Lol

The Paint job May Outlast Your Lungs! Wear Safety respirator at the least, A Full mask with respirator even better! What are yourungs Worth TO YOU?.....

you have a compressor i would consider letting the air out of the front tires to paint the hood ,that color looks good on that ford .

I sure do miss my 91 cougar at times

Thank you so much for this video

Just the video I was looking for. Awesome job 👍

Thank you

Do u even have to jack it up to do this ?

This video is still saving people trouble brother. Thank you 🙏🏻

Nobody cares wart u broke and the price of every thing just get to the part we're u put the tank in fuck

the costs now for tank, fuel pump & sending unit, fuel filter and straps with tax & delivery is $1,998.00 (and yes it is 35 gallon tank).

This was perfect, down to using the c-clamp! Thanks for the video!

is that the same Rust-Oleum oil paint that Lowes sells

Tell me you're from the salt belt without telling me you're from the salt belt.

Just loosen the lugs a bit, back up very slowly and tap the brakes. Repeat until tire breaks free.

Best advice to never give someone. Thx for posting

ridicules -

I have had to install a few trailer hitches that required this same method. Definitely a good trick to know

How you gonna tighten the bolt?

I have got gas leaking out on the ground when i fill it up all the way and then some more. Been like that for at least 7 years. Anyway, after seeing your Tank sitting there i saw the vent line and you said that hose was like a weak vacuum line and was rotted bad. Click! Maybe ,just maybe, thats my problem. I'm hoping it is. Easy fix,then. But It could be that sensor for the pressure though but i doubt it. Rust is not an issue since, its a Arkansas van 1994, well kept. Has 305,000 miles and I have owned it for 20 years. I don't like vehicle payments either and want to keep it going as long as possible. Gotta check it out asap before the snow flys here in Michigan, now. Your video is still helping people. So, Thanks. Bob R. Age 69 and still working on stuff.

Hows the physics works... ??? It is so lucky that wood and lift Jack didn't separate. But great video 👍

I might try and do this with an es300. Thanks for the video.

Sir, You put a new life to this truck, looks fantastic. Thank you for sharing. the technique snd experience.

Thank you for helping a young woman like myself change my break pads, I wouldn’t of been able to learn how without this exact video because I’m also cheap I can’t afford to buy alot so for now I got my break pads, my snowflake (jeep Cherokee 2000 sport) hasn’t had them changed in years! And now she’s got new pretty breaks ❤❤ thank you

Sorry, folks, this was my first attempt at a short and didn't realize My editing was bad. Please see the whole video at my channel. It's only a minute long.

The Heep isn't really that strong. The tree was so rotted I probably could have pulled it down with a car.😂

4 cyl engine with about 100k mi., the crosshatch honing pattern from original is STILL THERE perfectly visible... should I bother to rehone? There is no ridge, just some carbon ring at the top ..

I'm no safety nanny, but that looked like a pretty confined space, how were you not gasping on lacquer thinner fumes/vapour.? Need an airsource hood to wear, or do outside on a calm no wind morning.

mask brother....stuff is poison

We don’t need no stinking PPE!!

Mask ?

I got one, was your bolt bigger then the hole?